Hantek BNC to Dual Banana Head Test Line Leads HT30A+Back Probe+Attenuator HT201

Description: 1. Auto Test Leads (HT30A) Test lead of a male BNC connector to (2) 4mm connectors. It's a special line for assisting automobile measurement instruments to test various types of signals. 4mm connectors are coded in two colors, black and red. Lead length 3 meter.The Auto Test Cable (HT30A) is a kind of special line for assisting automobile measurement instruments to test various types of signals.It's about 3 meter in length allows the oscilloscope to be placed on the work bench away from the car being tested or repaired.It consists of wide range probes, clips, gators can be plugged into the 4 mm connectors at the end of the cable.It adopts full shield which can help reduce the noise interference.To avoide the lines twisting together, the two pieces of lines with connectors are not the same in length.The short line is earth wire, and the long line is positive pole which should be connected with the auto engine cable, which also can cooperate with a 20:1 attenuator.2. Large Dolphin/Gator Clips (HT18A) The dolphin/gator clips are fully insulated with a 4 mm socket in the handle, offering an easy connection to the HT30A auot test cable. The toothed grip offers good contact on fine wire, with a 30 mm jaw opening limit.Length: 85 mmHeight: 38 mmDepth: 16.5 mmClamping limit: 30 mmContents: 1pc X Red Clip; 1pc X Black Clip3. Acupuncture Probe Set (HT307) This acupuncture probe is a back pinning, piercing and repairable probe; The HT307 Back Probe Pins have many uses, such as back probing, piercing, and pin-tip probing. The fine tip can slide past weather pack seals to probe connectors. They are sometimes referred to as acupuncture probes, in which they are used for piercing the insulation of wires to allow for automotive electrical measurements without causing damage to the wires. Additionally they can be used as pin-tip probes while working with small circuit boards.If a pin should bend or break during use, the set of 5 probes also comes with 10 replacement pins. To replace, use a hex key to remove the set screw and damaged pin. Then simply put in new pin and replace the set screw. The probe has a female banana plug for use with your oscilloscope.Firstly, it's a back pinning probe. In fact, it's the smallest diameter back pinning probe that we know of. This is essential for probing today's small, fragile connector. It is also very sharp, so it slides past connector seals with ease. This product solves most of the problems associated with traditional back-pinning methods.Secondly, it's a piercing probe. Its small diameter, extra sharp pin makes it ideal for piercing the insulation on small gauge wires where traditional piercing tools might cause damage.Finally, here's the best part-it's repairable. If the pin becomes damaged or useless in any way, simply take your pocket screwdriver, remove the set screw, pull out the old pin and install the new one! There's no need to replace the whole probe.Contents:5pcs Complete acupuncture probes (needles are bendable)2pcs Screws20pcs Replacement needles (bendable) 4. 20:1 Attenuator (HT201) Designed for assisting automobile measurement.The HT201 has been designed to allow fuel injector and primary ignition waveforms to be measured using Hantek oscilloscope products. Please note: this attenuator should not be used for any high voltage measurements other than fuel injectors and primary ignition.Attenuation: 20:1Bandwidth: 10MHzInput Res: 1.053M5. 5 Pcs Protective Probes These piercing probes are 4mm standard female banana plug seat at the end,can connect most of test lead ,diagnostic devices and automotive testing,widely used in auto /electrical testing.With protective shell ,can ensure your safety and free your hands. Voltage : Max 30V Surface Material: PA Nylon / Brass Needle Material: Stainless steel Connection: 4mm Banana Plug Color: Red, Black,Yellow,Green,Blue each 1 Package List:1 * Auto Test Lead 2 * Gator Clips5* Complete Acupuncture Probes (with 10 * Replacement Needles)1* HT201 Attenuator5* protective probes

Price: 29.88 USD

Location: Anshan Liaoning

End Time: 2024-08-28T14:45:07.000Z

Shipping Cost: 5.85 USD